2010-14 Camaro Turbo System – LS2 / LS3 / LSX – MANUAL TRANSMISSION ONLY

(11 customer reviews)

$2,659.00

Up until this point we have directed a lot of our attention to the Mustang market and all along seen the potential of the LSx platform. We have also designed two turbo systems for the 1998 – 2002 LS1 F-Body, check our site for those kits as well. After getting the 2010 Camaro delivered to our shop, it didn’t take long to layout and design the newest and first GM application that we will be offering. This kit is set to be released by the end of May 2012.

As for our kit design, we started by building a hotside that would merge together on the driverside and hold one of our 70mm On 3 Performance turbochargers. This is the same turbocharger that’s been on our shop 2002 Mustang GT for the last 4 years and has been daily driven since then. We have put over 20,000 miles on that car and the turbo has proven the test of time and put through a ton of abuse. We use this turbo in almost all of our kits and will have no problem supporting up to around 650rwhp on this application. We do also have the On 3 Performance 76mm turbocharger available for this kit as well and you can find in the optional items down the page. Directing the gas out of the turbo is a single 3” downpipe built to merge into the factory exhaust just behind the transmission. All of the exhaust connections are v-banded and we supply 1 lap-band to attach the downpipe to the factory exhaust. That way its all a simple bolt on without welding that anyone semi-mechanically inclined will have no problem installing.

Moving on to the cold side of the kit, we have built a 3” charge pipe that feeds the intercooler and coming out of the intercooler to the throttle body transitions into 3.5”. Each kit comes with our crossflow 3” On 3 Performance bar and plate intercooler. We also have a 4” core that is available as well and listed under our optional items if you plan on maxing out your shortblock or if you have a built motor going for higher boost levels. Our 5 ply On 3 Performance silicone couplers connect each intercooler pipe together and t-bolt clamps ensure maximum clamping force and prevent any intercooler pipes from blowing. Each pipe is bead rolled on both ends to add extra protection from losing a pipe under boost. On to mounting your intercooler, we supply you CNC laser cut and formed mounting brackets to hold the intercooler in place

This is a bolt on system which is going to allow for a straight forward install. We include an instruction package with the kit that will detail the install and have photos to help those visually see how it goes together.

Need Help Choosing The Proper Turbo?

If you do not know what you are doing with turbo sizing, please call in for advice. We do not want to see you ruin your turbo from lack of proper understanding about motor cubic inch size and turbo exhaust wheel sizing. We most commonly see this when our customers try to put a 65 exhaust wheel on a 6.0 or larger motor. The rule of thumb is the larger the motor, the larger the exhaust wheel you are going to need. If you put too small of a turbo on too large of a motor, the turbo will fail due to this. Again, if you have questions, please call. We can’t possibly know what your project/swap is if you order the kit off of the website without reaching out to us first. Generally, a 70/65 or 76/65 turbo will be just fine for a fairly stock 4.8L or a 5.3L motor, but not ok when you step up into a 6.0. The 6.0L and 6.2L motors should have a 78/75 or larger turbo, depending on the build. Understand that the 76/75 BMF is fine as well, and will actually generate more power than the 78/75. If you are building a 408 or larger, we recommend going with an 88/84mm turbo or a T6, depending on what you are trying to accomplish.

AUTOMATIC TRANSMISSION QUESTIONS:

On a daily basis we are asked about the kit fitting automatic cars or why does it only fit manual cars.  We designed this car on a 6sp car and the crossover from the pass. side manifold to the turbo manifold crosses under the transmissions.  We could not calculate for the automatic transmission pan when designing the kit.  This is not to say it will not work but if you HAVE and automatic transmission car, you would need to modify the crossover at least to make it clear and go under the transmission.  This is not a service we can provide, this is completely up to the end user

Description

Customer sent in his car getting tuned and putting down over 600rwhp:

 

Here is a clip we found of a customer in KY making a pass running the On 3 single turbo system:

 

Hotside

  • On 3 Performance Custom 304ss Driverside Side Turbo Manifold, T-4 Flanged
  • 2.5” 304ss 2.75mm Wall Crossover Pipe
  • On 3 Performance 3” Stainless Downpipe (Pre-welded for wideband)
  • V-band Clamps For Each Exhaust Connection

Coldside

  • Driver side Tubing From Turbo To Intercooler and Intercooler to Throttle Body
  • On 3 Performance 5 ply Custom Silicone Coupler Kit
  • All T-bolt Clamps For Couplers
  • On 3 Performance Bar & Plate Crossflow Front Mount Intercooler

Kit Contents

  • On 3 Performance 78mm Turbocharger (78/75), .80ar Cold, .96ar Exhaust Housing **Now Standard!!!!
  • On 3 Performance 44mm V-band Wastegate
  • On 3 Performance 50mm Blow Off Valve
  • On 3 Performance Custom Oil Feed Lines / Drain Kit
  • Custom Laser Formed Intercooler Mounts
  • Vacuum Line For Wastegates
  • Vacuum Line For Blow Off Valve
  • Hardware Kit
  • Instruction CD w/ Photos

Shipping

  • This kit is a Flat Rate $99 to any location within the lower 48 States.
  • Shipping will be visible and itemize in cart upon checkout.

 

 

11 reviews for 2010-14 Camaro Turbo System – LS2 / LS3 / LSX – MANUAL TRANSMISSION ONLY

  1. Bill R.

    When will this kit be available again? Do you offer it in a twin upgrade or can you make it specifically for twins? Thanks

    • admin

      We should be taking orders on this system within the next 6 weeks we hope as of right now. The production is scheduled and just a time consuming process

  2. Patrick

    System Is working great, making 560whp/580/torque at the moment and it can do more. Going to do a fuel system next so I was wondering if there was a way to do the 88mm, with the 4″ cooler? Do you make adapters so it will bolt right up?

    • admin

      Thats good to hear, you can simply upgrade to the 4″ race core without any other changes. The 88mm however is a pretty large turbo so its not going to be a bolt on. It for sure will require custom down pipe work and since we have never fit that to a 2010+ Camaro personally, I cannot confirm specifically what else it might possible involve

  3. Ali

    hi . when this kit will be ready for sale ? now your 6 week done

  4. ali

    you dont have eney thing to sell you only blablabla
    like the z06 kit
    copy from other kits

  5. Ramon Coto

    when would this kit be on stock I need this kit asap!

    • admin

      It is in stock and ready to order, shipping daily!

  6. Bill R.

    I continue to check into this kit on a regular basis, and these kits are always OUT OF STOCK. Are you going to stock these? Or will they be built to order? If they are built to order can you make this kit in a twin turbo with headers? I’m looking to produce 750-800+whp with room for adjustability. My email is included please contact me with options, I’m willing to be a guinea pig given the right options. Thank you.

  7. sd22guy

    when with this kit be available I’m ready to order

    • admin

      It is in stock and ready to go whenever you are. I just corrected the inventory so you are good to order

  8. Matias Myhren

    Would the 84mm Ceramic Ball Bearing Turbo Upgrade still be all “bolt on,” or do I need a smaller one for it to still be bolt on. Because Im planning on getting the fuel injectors and literally all the add ons on the list i just wanna make sure what turbo size would be the best if I’m getting all the parts. You can also email me, Thank you

    • admin

      The 84mm turbo is the largest turbo that will bolt on any of our systems setup for the t4 flange

  9. Gashgari

    Hi. do I have to delete the AC with this kit? thanks

    • admin

      You keep all accessories like like a/c and p/s

  10. Rigo

    do you have any in stock I’m ready to order?

    • admin

      Yes I keep this kit in stock at all times

  11. Jesse

    Can this be modified at all to work on a auto?

    • admin

      Sure we have plenty of people that cut the crossover and make it work with the automatic transmissions

Add a review